Prices  | Theory  | Online videos  |  Downloads  |  Home | E-mail | Site Map

Search This site The web

   


 

 

 

 

 

 

V2 features ] Flash tutorials ] FAQ ] V2 Build update ] V2 Compatibility ] V2 Installing ] V2 Serial Numbers ] V2 Upgrading ] V2 Maintenance Policy ] Register MIDUSS ]

Frequently asked questions

 

Got a question?
Email:

My quesion is:

Channels

 

V2 = applies to MIDUSS Version 2 (current release)
M98 = applies to MIDUSS 98
  • [ M98 ][ V2 ]   When I use the Channel design the only way I can define the shape is in terms of a simple trapezoidal cross section. My channel is more complicated than this. How can I do this?

The channel design in MIDUSSS can use a simple trapezoidal shape or an arbitrary cross section made up of lines joining a set of up to 50 coordinate pairs. To use this you must click on the check box labeled "Define arbitrary cross section." This will then allow you to draw and refine a channel cross section which can be as complicated as you wish.   [ V2 ] You can save the cross section to file for use later on or during another session.

  • [ M98 ][ V2 ]    When I start to draw the channel cross section a line appears leading to the first point that I have defined. What is this for?

This line will disappear once you have specified the entire cross section and presses the [OK] button.

You define the points of the arbitrary cross section moving from left to right. In order to mark each point you must use the primary (or left) mouse button. To finish defining the points you must click the last point using the secondary {or right} mouse button.

After you have defined all of the coordinate pairs you must click on the [OK] command button in the bottom right of the form. This will enable the [Design] button.

The channel depth can be entered only for a simple trapezoidal cross section. When you define an arbitrary cross section with a number of points the channel depth is automatically computed and displayed for information.

  • [ M98 ][ V2 ]    I was able to design a channel with an arbitrary cross section but after changing the gradient or the Manning Ďní value the computed water surface disappeared. Why is this?

Once a design has been completed any change in the data will cause the computed water surface to be erased. This forces you to use the [Design] command button once again to update the design.

  • [ M98 ][ V2 ]    When trying to draw a channel cross section my points were not very accurate. I want to make the section symmetrical. How can I do this?

Once all of the points have been drawn approximately, you can edit these by typing in numerical values in the table below the drawing window. You can either specify the X and Y coordinates explicitly or you can change one of the secondary parameters such as the horizontal (dX) or vertical (dY) distance between points.

  • [ M98 ][ V2 ]    In editing the data defining an arbitrary cross section I notice some of the values are negative. Why is this?

It is quite possible to have negative values since these represent the difference between two adjacent points moving from left to right. A negative value indicates a reduction in elevation. Similarly, the slope defined by the (dY/dX) parameter may be negative implying a downward slope.

  • [ M98 ][ V2 ]    I designed a channel with an arbitrary cross section but it was too narrow. I want to change the design by widening the low flow channel. Do I have to enter all the points again?

No. You can increase the width of only one line segment in the cross section. This can be done by typing in a new value for the dX value for a line segment. When you do this all of the points to the right of that line segment will be automatically moved to the right.


(c) Copyright 1984-2010 Alan A. Smith Inc.
Terms and Conditions       Privacy Policy      Contact Webmaster


Design makes
the difference
Latest Update:
v2.25 Rev468
March 6, 2009
On-line videos

There are 25 Flash videos available to help you use MIDUSS.  Click here.

Quick Story

How about a quick MIDUSS review in 180 seconds or less? We know your time is valuable. Click here for the fast story.

College or University faculty?

Please see our academic page for our low price offer.  Click here.

MIDUSS Automatic Mode Problems?

Recent Windows XP and 2000 updates have caused some MIDUSS 98 and Version 2 installations to fail in Auto mode.  If you are experiencing this problem click here.

Theory anyone?

If you are interested in the hydrological or hydraulic theory built into MIDUSS click here.

What do MIDUSS users say

View the results of our May 2004 User survey.  No marketing fluff, just the facts.  Click here.

Malaysia
You have a custom version of MIDUSS distributed through Winz Connections.
Find out more informaion about the custom Malaysia storms.  Click here.
 

 

 

 

 

 

 

 

 

 Up ] FAQ General ] FAQ Operations ] FAQ Storms ] FAQ Catchments ] FAQ Hydrographs ] FAQ Pipes ] FAQ Ponds ] [ FAQ Channels ] FAQ Routing ] FAQ Automatic mode ] FAQ Diversions ]